The All-in-One
Interior Design & Furniture Families
All of the built-in features in the All-in-One Interior Design & Furniture Families were designed from the ground up to take advantage of the advanced parametric capabilities of Revit. So you can create almost any Kitchen, Cupboard, Wardrobe, Locker, Shelf, Chair, Sofa, Stool, Lighting Fixtures, etc. with just one single Revit Family that you can not do with any other Revit Family.
These parametric Revit Families are developed by a Team of Architects and Revit® Professionals to give you the possibility to setup countless objects with just one single Family rather then to use various Families.
Kitchen
The All-in-One Kitchen Family is the best and most flexible way to create Kitchen casework in your Revit Project. This fully parametric Revit Kitchen Family lets you setup floor, wall and corner units with single and double swing leafs, sliding leafs, drawers as well as open shelves and combinations. The fully parametric door leafs adjust automatically to your casework shell setup as well as your choice of leaf type. Additional to conventional units, oven, sink, and other options allow you to create an entire Kitchen out of just one parametric All-in-One Kitchen Family.
|
|
 More Flexibility with Corner Units NEW (Ver. 3.4)
With Version 3.4 the All-in-One Kitchen Unit adds even more flexibility for setting up your individual Corner Unit with the new 45 degrees Corner Unit as well as the free adjustable Worktop which solves now all the nasty corner solutions were the walls do not meet at 90 degrees.
|
 More Flexibility with Drawers NEW (Ver. 3.3)
With Version 3.3 the All-in-One Kitchen Unit gives you more flexibility to setup the Drawer Unit you need. You define how many Drawers and if you need a fix Height or if the should be fitted in height automatically. This is an amazing simple to use feature and makes the best Revit Kitchen Family even better.
|
Any Corner Unit NEW (Ver. 3.2)
With Version 3.2 the All-in-One Kitchen Unit lets you setup any combination of a Corner Unit. You are not limited to just doors on each side as you can now simply adjust any Unit you can setup with this amazing Revit Kitchen Family to be part of the Corner Unit.
|
Double Bowl Sink / Parametric Tap NEW (Ver. 3.0)
The fully Parametric Sink can now be either with one or with two bowls. To add the second Bowl is just one click and it can be adjusted in its position, width, length, depth as well as radius. Together with the parametric Drainer, almost any Sink setup can now be done to fit exact your project specific requirements. Additional to the second bowl, the sink comes now with a fully parametric tap that can adjusted in its positions, to various shapes and even be rotated.
|
Extractor Fan NEW (Ver. 3.0)
The All-in-One Revit Kitchen Family lets you now add a fully parametric Extractor Fan. This Extractor fan can be activated with just one click and then be adjusted in its shape, size as well as position. This way you can setup exactly the Extractor Fan you need for your Revi–t Project either it is for a wall mounted kitchen or a free standing Kitchen Island.
|
Swap Drawer / Door NEW (Ver. 3.0)
It is very easy to setup a combination of Door and Drawer(s) with changing just a few Parameters. You can change between a single and double Door with just one click and choose the number of Drawers by adjusting just one Parameter. Now you can even swap the position of the Door and the Drawer(s) with just one single click.
|
Drawers Unit with Height Lock
This Revit Kitchen Family lets you setup a Kitchen unit just with Drawers. In previous Versions the Height of the Kitchen Unit was automatically adjusted by the number of drawers. The Version 3 lets you lock the Height of the Kitchen Unit which results in automatically adjustment of the Drawers Height.
|
Kick Plate / Legs NEW (Ver. 2.0)
Every Unit can now been setup for either a Kick Plate or with Legs. And that isn't all ... as you can have full control over every single Leg with just one Parameter. Additional the Shape as well as Dimension of the Legs can be fully controlled. In case that you would like to use the Kick Plate, it allows you now to setup a separate Material.
|
Floor Corner Unit NEW (Ver. 2.0)
One of the most asked features ...
It took us quite a while (and a few hours evaluating various IKEA Kitchen Types) to find a really optimized way to still use the original Kitchen unit without having any Element double, just controled with parameters |
Wall Corner Unit NEW (Ver. 2.0)
If there is a normal Corner Unit, a corner Wall unit is obviously a must have ...
It is still the same Kitchen Unit, just changing a few Parametrs ... and you have a fully adjustable Wall hung Corner Unit.
|
Symbol Lines in Elevation & Plan View NEW (Ver. 2.0)
The Kitchen unit shouldn't just be gorgeous in a 3D view, or ?
Just look at it with an elevation view or an plan view and get a ready Kitchen Plan with all Symbol Lines in Elevation as well as Plan view.
As our customers come from all over the world - we have taken care about localization as well - Yes, you can even controll the direction of the Symbol Lines as they are variating in different countries ... Arrow from or to Hinge.
|
Cooker
The Kitchen Unit can be adjusted to a Cooker with just a few Parameter. The Oven Front as well as the cooker are fully parametric and can be fully adjusted. |
Sink
The Kitchen Unit can also be adjusted to a sink with just a few Parameter. |
Backsplash NEW (Ver. 2.0)
What would be a kitchen without Backsplash ?
If you would like Tiles or colored Glass, the fully parametric Backsplash gives you any possibility as it has it's own Material Parameter. Of course you can control the Visibility as well as the hight of the Backsplash -it's obvious, isn't it ?
|
Double Door Floor Unit
You have to choice to adjust the Kitchen Unit either to Swing Doors or Sliding Doors. |
Drawer Floor Unit
The Kitchen Unit can also be adjusted to Drawers ... of course fully parametric ... so you choose how many Drawers ... |
 Single Door Floor Unit
To switch between a double or single Door Unit, just change one single Parameter.
|
Double Door Wall hung Unit
The same what you can setup for a Floor Unit can be done for a Wall hung Unit, again with just a few Parameter. |
Shelve Wall hung Unit
If you don't want Doors, just switch them off ... |
 Single Door Wall hung Unit
And again, the same single Door Unit that you can setup as Floor Unit can be adjusted as Wall hung Unit, changing just a few Parameter.
|
|
Cupboard -
Wardrobe
The All-in-One Cupboard Family is the best and most flexible way to create any Cupboard, Wardrobe, Shelf casework in your Revit Project. This fully parametric Revit Cupboard Family lets you setup floor, wall and corner units with single and double swing leafs, sliding leafs, drawers as well as open shelves and combinations. The fully parametric door leafs adjust automatically to your casework shell setup as well as your choice of leaf type.
|
 |
The Concept
The All-in-One Revit Cupboard Family is a new and unique way to create Revit Furniture Families. This Revit Furniture Family is fully parametric and gives you any Cupboard, Wardrobe, Shelf, Locker, etc. you require for your Revit project in just one single Family. To maintain your Revit Furniture and keep them consistent in design has never been easier then with this All-in-One Revit Cupboard Family that lets you build Floor-, Wall- and Corner Units.
|
The Shell
The flexibility of this Revit Cupboard Family starts with its parametric Shell which can do much more then just be adjusted in Width, Depth and Height. It allows you to control it’s visibility, thickness, as well as top and base adjustments.
|
 |
 |
Door Panels
The Door Panel Feature gives you the possibility to change between a single or double swing or sliding door that can be either solid or framed with glazing, so it is easy to setup one type with the right shell, base and top and multiply this type with various front solutions.
|
Drawers
You are not limited to just Door Panels as this Revit Cupboard Family lets you also setup various Drawer Configurations. This allows you with just a couple of clicks to setup a mixed Drawer Unit or you can mix Drawers with Door Panels - it’s all just a few clicks as this Revit Family is smart to adjust the Unit for you.
|
 |
 |
Floor - Wall - Corner Solutions
Once you have chosen your required type from the included Type Catalog or you have setup your own specific type, you can use this type either as Floor-, Wall- or Corner Unit.
|
Accessories
As this All-in-One Revit Cupboard Family is a casework category, you might want to cut it to show the parametric Shelves, Dividers as well as the Pole that comes as Accessory with this magically flexible Revit Furniture Family.
|
 |
The Shell
The Shell - Closed / Partly Open / Open
The Shell - Closed / Part Open / Open
The All-in-One Revit Cupboard Family allows you to control the visibility of the side & back Panels to have either a fully closed unit or with open front and back and of course without any shell. So it is your choice to build a closed cupboard positioned at a wall, a room divider shelf with a frame and open front and back or a freestanding wine shelf without any shell.
|
 |
The Base
You might want to build a Floor Unit positioned at a wall with a recessed kick-plate or a Row of Lockers based on squared legs ...
With this fully parametric Cupboard it is at your fingertip how your unit-base looks like.
|
|
The Top
Finally there is the top of your furniture unit which might be just the blank shell or you decide to add a top which can be anything from a slim flush glass to an overhanging solid top.
|
 |
Door Panels
 |
Swing / Sliding
The All-in-One Revit Cupboard Family allows you to switch between a Swing or Sliding Door in the same simple way as you switch between a single or Double Door.
|
 |
Solid / Framed Glazing
Once you have decided for the Door System you want to use with your unit it is just one more click to switch between a solid or framed Door Panel which can then be further adjusted in detail.
|
Symbol Line
The All-in-One Revit Cupboard Family shows your setup of Doors and the Hinge Positions with 2D and 3D Symbol Lines in Elevation and Plan view. As our All-in-One Families are in use in more then 100 countries worldwide the Symbol lines can also be adjusted to your local standards.
|
 |
 |
Drawers
Just Drawers
The All-in-One Revit Cupboard Family offers you a very smart way of building your Drawer unit. With just one click you activate the ‘Just Drawer’ Mode and the entire unit follows your Drawer adjustments.
Divide your drawers equally
If you want the Unit to keep its height and to automatically adjust the Height of the Drawers - no problem. This smart All-in-One revit Cupboard Family allows you to lock the unit height with just one click and all your drawers are adjusted automatically in their height.
|
 |
Combine Drawers & Door Panels
You can combine Door Panels with Drawers in the same simple way by to build units with Drawers above or underneath the Door.
|
 |
Floor - Wall - Corner Solutions
 |
Floor Unit
The All-in-One Revit Cupboard Family lets you build Floor Units with various Base and adjustable Top setups.
|
 |
Wall Unit
Duplicate a ordinary Floor Unit, change a couple of Parameter and you get a Wall Unit. It has never been easier to get so much flexibility by keeping the style constant.
|
 |
Corner Unit - 45 / 90 degrees
This new Feature allows you to activate a 45 or 90 degrees Corner Setup simply by activating one parameter. Several detail parameter allow you to adjust both sides of the Corner Unit exactly to your requirements. You can even combine various units to corner units with smart and flexible parameters that allow you to adjust elements in various details.
|
 |
Mitered Corner Unit
Another new Feature to achieve more complex arrangements is the mitered corner unit which allows you to build solutions for corners different to 90 degrees as you might find them in existing buildings.
|
Accessories
Shelves / Dividers
Fully parametric Shelves and Dividers give you the possibility to build book shelfs, wine racks, and much more ...
Pole
A fully parametric Pole rounds up the interior accessories in this All-in-One Revit Cupboard Family to allow you to build a detailed wardrobe.
|
|
Bench
If you want to build a Locker, this exterior accessory gives you a fully parametric Bench.
|
 |
Seating
The All-in-One Seating Family is the best and most flexible way to create any Chairs, Sofas and Stools for residential, office and commercial Revit Projects. This fully parametric Revit Seating Family lets you setup Dining Chairs, Office Chairs, one and multi seater Sofas as well as various types of Stools with just one single parametric Revit Family.
|
 |
The Concept
The All-in-One Seating Family is a new member of our All-in-One Furniture Family Series which makes it simple to build countless different seating furniture with just one single Revit Family. This Revit Seating Family is fully parametric and can therefore be adjusted to almost any Sofa, Dining Chair, Office Chair, Stool, etc.
|
Sofas
The All-in-One Seating Family is fully parametric and allows you to adjust the Family with just a few parameters to various Sofas with either a full base or various leg options. You need just to change the width and the number of modules you wish to setup and you get from a single sofa to a multi-seater sofa everything within seconds.
|
 |
 |
Dining Chairs
The All-in-One Seating Family is not just limited to sofas ...
Just change the width and depth and the thickness of the armrest as well as backrest and you get a beautiful dining chair. Or switch off the armrest and you get a normal chair. It can’t be simpler and faster ...
|
Office Chairs
In case that you need an office chair, it’s just one more parameter to change and the legs transform to typical office chair legs. You can even adjust the number of segments, the shape, angle, and much more to make the perfect office chair for your Revit Project.
|
 |
 |
Stools
And finally the All-in-One Seating Family lets you setup Stools by just switching off the backrest ...
|
 |
Table
The All-in-One Seating Family is the best and most flexible way to create any Chairs, Sofas and Stools for residential, office and commercial Revit Projects. This fully parametric Revit Seating Family lets you setup Dining Chairs, Office Chairs, one and multi seater Sofas as well as various types of Stools with just one single parametric Revit Family.
|
The Concept
The All-in-One Table Family is a new member of our All-in-One Furniture Family Series which makes it simple to build countless different table furniture with just one single Revit Family. This Revit Table Family is fully parametric and can therefore be adjusted to almost any Dining Table, Office Table, Bar Table and Coffee Table, etc.
|
Dining Table
The All-in-One Table Family is fully parametric and allows you to adjust the Family with just a few parameters to various Dining Tables with various leg and top options. The Family has been designed to switch between different leg options just by changing one single parameter, which makes this family simple to use but yet very powerful.
|
 |
 |
Office Table
The All-in-One Table Family is not just limited to Dining Tables...
Just change one more parameter and the table switches to a corner table which is very common in Office Projects. Change the Width and Depth and you get a meeting table, etc.
|
Bar Table
Do you design restaurants ?
The All-in-One Table Family transforms without effort to any Bar or Restaurant Table and will help you to get your furniture easily done in your Revit Project.
|
 |
 |
Coffee Table
And finally the All-in-One Table Family lets you of course setup a Coffee Table too.
|
Lighting
The All-in-One Lighting Family is the best and most flexible way to create any Lighting Fixtures in your Revit Project. This fully parametric Revit All-in-One Lighting Family is face based and lets you therefore setup Ceiling Lights, Downlights, Wall Lights, Table Lamps and Floor Lights. As this All-in-One Lighting Family is based on the Revit Lighting Fixture category, it has integrated Photometrics to allow you to setup the light for your photorealistic Renderings.
|
|
The Concept
The All-in-One Lighting Family is a new member of our All-in-One Furniture / Interior Family Series which makes it simple to build countless different lighting fixtures with just one single Revit Family. This Revit Seating Family is fully parametric and can therefore be adjusted to almost any Ceiling Lights, Spotlights, Wall Lights, Table Lamps and Floor Lights etc.
|
Ceiling Lights
The All-in-One Lighting Family is fully parametric, face based and allows you to adjust the Family with just a few parameters to various Ceiling Lights mounted to the ceiling or suspended from the ceiling. The shape of the lamp can be changed by adjusting just one single parameter which gives you great flexibility within seconds.
|
 |
 |
Recessed Downlights
The All-in-One Lighting Family is not just limited to surface mounted lightings ...
Just activate the Recessed - Feature and you are free to adjust your recessed downlight from round to squared, rectangular, with and without round corners . It can’t be simpler and faster ...
|
Wall Lights
The All-in-One Lighting Family is face based which makes it very simple to just drop it on any surface like ceilings, tables, worktops, floors or walls. The connecting tube between the base and the top can be adjusted in its profile, length as well as angle which gives you great flexibility to setup your specific wall light.
|
 |
 |
Table Lamps
The All-in-One Lighting Family can be placed on any furniture top and adjusted to a table lamp for residential or office use.
|
Floor Lamps
The All-in-One Lighting Family is also a floor lamp. Just place it on the floor, adjust the length of the connecting tube between the base and the top and setup the shape and material of the top fitting to your project design.
|
 |
 |
Switch the light on
And finally the All-in-One Lighting Family lets you switch on the light for realistic renderings and adjusting it with its integrated Photometrics ...
|
Mac® Computer
The All-in-One Mac® Computer Family is the best and most flexible way to create any Mac® Computer in your Revit Project. This fully parametric Revit All-in-One Mac® Computer Family is face based and lets you simply place iMac®, MacBook®, iPad® as well as iPhone® on any Surface within your Revit Project. A great accessory for your photorealistic Interior Renderings.
|
 |
 |
iMac®
The All-in-One Mac® Computer Family makes it simple for you to place a detailed iMac® straight in your Revit Project. The Family comes with a metric and imperial Type Catalog inlcuding the 21.5-inch iMac® as well as the 27-inch iMac® so that you just need to place it in your project.
|
MacBook®
The All-in-One Mac® Computer Family is fully parametric and allows you to adjust the Family with just a few parameters to the latest 13-inch, 15-inch or 17-inch MacBook® Pro Model or you just select it from the included Type Catalog. As this Revit Family is face based, you can easily position on tables or any other face based elements.
|
 |
 |
iPad®
The All-in-One Mac® Computer Family lets you even go further. Transform your Mac Computer with the adjustments of a few parameters to the new iPad®, either placed on a dock or table.
|
iPhone®
And finally the All-in-One Mac® Computer Family can also be transformed to an iPhone®, either placed on a dock or a table.
|
 |
Become a Fan on Facebook
Follow us on Twitter
Follow us on Blogger